home
***
CD-ROM
|
disk
|
FTP
|
other
***
search
/
Tech Arsenal 1
/
Tech Arsenal (Arsenal Computer).ISO
/
tek-06
/
ps2cmb.zip
/
PS2CMB.DOC
< prev
next >
Wrap
Text File
|
1991-09-18
|
8KB
|
194 lines
This README file of PS2CMB.ZIP for NetWare v2.2 and v2.15C.
The following files are included for this revision:
COMB OBJ 12645 5-23-91 1:59p
DUMMY OBJ 138 5-23-91 1:59p
SCSICOMB DSK 564 9-10-91 10:20a
ESDICOMB DSK 1292 9-10-91 10:22a
Novell ESDI/SCSI Combination Driver Set
WARNING: Before you begin this installation, back up your
system to avoid losing any important data.
If you are installing on a v2.2 network, use the Advanced
installation. Do not use Basic Install.
To install the new ESDI/SCSI combination driver set in
your PS/2 Model, complete the following steps:
1. Follow the instructions for installing drives and
disk controllers in your IBM documentation.
Don't autoconfigure the system. Continue with Step 2.
2. Run REFERENCE.
3. From the main menu, choose Option #2 ("Set
Configuration")
4. From the "Set Configuration" menu, choose Option #1
("View Configuration") and record the following
information:
o I/O addresses
o DMA
5. From the "Set Configuration" menu, choose
Option #6 ("Set and View SCSI device
configuration").
Check to be sure the SCSI configuration matches your
recorded configuration information.
6. When configuration is completed, choose Option #7
("Display Memory Map").
Record the hexadecimal addresses for each driver
as shown on the screen.
Note: If your system includes more than 2 hard drives and you are
running DOS 4.0, you must install the DOS v4.0 Corrective
Services Diskette (CSD #UR29015). This diskette is available
from IBM. The system must be booted with DOS 4.0 or
higher.
7. Follow the instructions on the screen to exit
REFERENCE.
The following installation instructions are divided into two
categories:
o v2.15
o v2.2
Scroll through to find the section that applies to your specific
system. You are now ready to begin the installation process. These
procedures vary between v2.15 and v2.2 systems. There are
no defaults available for this installation. You must load the
ESDI and the SCSI shared int 14 drivers. The operating
system will be unable to link if both drivers are not loaded.
Note: All driver configuration options must correspond to
actual hardware settings. Software adjusts must be
accompanied by hardware adjustments and vice versa if
either are necessary.
NetWare v2.15 Installation (Custom)
Refer to the NetWare v2.15 Maintenance manual for
installation instructions. Before running NETGEN complete
the following steps:
1. NETWORK DRIVE: Create a directory called
DSK_DRV_.031.
FLOPPY DRIVE: Format a diskette with the label
DSK_DRV_031. Use the DOS FORMAT /V command.
2. NETWORK DRIVE: Copy the .DSK in the AUXGEN
directory and the .OBJ files into the directory you
created in Step 1.
FLOPPY DRIVE: Copy the .OBJ files and the .DSK
files to the newly formatted diskette you created in
Step 1.
3. Run NETGEN.
4. NETWORK DRIVE: Choose "Select Loaded Item" from
the menu and continue with Step 5.
FLOPPY DRIVE: Complete the disk driver installation
instructions contained in the Maintenance manual.
Then continue with Step 5 below.
Note: As you install new disk drivers, you may see a message
similar to the following:
"Driver 1 has the same type number as Driver 2.
Replace Driver 1 with Driver 2?"
The drivers do not always appear in the same order,
indicating that Driver 1 is not necessarily the new driver.
Be sure you select the ESDI shared int 14 driver.
5. Choose the ESDI shared int 14 driver from the list and
press <Enter>.
6. Highlight Configuration Option and press <Enter>.
Highlight the option you recorded earlier and press
<Enter>. 7. Repeat Steps 5 and 6, this time choosing the SCSI
shared int 14 driver.
8. Continue with the file server installation as usual,
following the screen prompts.
NetWare v2.2 Installation (Advanced)
1. Use the DOS LABEL command to format a blank
diskette. Label the diskette DSK_DRV_031 and
copy the following files onto it:
o .OBJ
o .DSK
2. Copy the driver and description files to the
DSK_DRV_031 diskette.
3. Complete the installation instructions contained in the
documentation for NetWare v2.2, through Step 12 on
page 36. Then continue with Step 3 below.
4. Press <Insert>.
5. Insert the DSK_DRV_031 diskette into a floppy
diskette drive and press <Enter>.
6. Choose the ESDI shared int 14 driver from the list and
press <Enter>.
7. Highlight Configuration Option and press <Enter>.
Highlight the option you recorded earlier and press
<Enter>.
Note: An asterisk (*) next to a selected driver indicates that the
option conflicts with other hardware configurations selected.
All driver configuration options must correspond to
actual hardware settings. Software adjustments must be
accompanied by hardware adjustments and vice versa if
either are necessary.
8. Repeat Steps 5 through 7, this time choosing the
SCSI shared int 14 driver.
9. Press <F10> when the form is complete.
This step saves the configurations as entered. Continue
the installation as usual from this point.
*****************************************************************
DISCLAIMER
Novell, Inc. makes no representations or warranties with respect to
any NetWare software, and specifically disclaims any express or
implied warranties of merchantability, title, or fitness for a
particular purpose.
Distribution of any NetWare software is forbidden without the
express written consent of Novell, Inc. Further, Novell reserves
the right to discontinue distribution of any NetWare software.
Novell is not responsible for lost profits or revenue, loss of use
of the software, loss of data, costs of re-creating lost data, the
cost of any substitute equipment or program, or claims by any party
other than you. Novell strongly recommends a backup be made before
any software is installed. Technical support for this software
may be provided at the discretion of Novell.
*****************************************************************